Search problems & products
Thank you for printing our content at www.fixya.com
Question about Adtran NETVANTA 1234 POE 24PT LAYER2 SWCH POE 1700595G1 Ethernet Switch
people viewed this question
Posted by ckloehr on Mar 18, 2011 Talk to an Expert
Adtran NETVANTA 1234 POE 24PT... Adtran Computers & Internet
Get Instant Help
How do you reset adtran netvanta 1234 back to factory? Related Topics:
Ask a Question Usually answered in minutes!
What do you need help with?
2 Suggested Answers 6ya staff 2 Answers
SOURCE: I have freestanding Series 8 dishwasher. Lately durin…
Hi, a 6ya expert can help you resolve that issue over the phone in a minute or two. Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US. the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones) click here to download the app (for users in the US for now) and get all the help you need. Goodluck! Download 6ya
Need repair answers fast Use 6ya to...
Adtran NetVanta 1224R 24-Port...
How do I reset an Adtran Total Access 908 Router...
Netvanta reset password Adtran NetVanta 3200 Router
Forgot password of Adtran NetVanta 1224R Switch
Posted on Jan 02, 2017 2.3K
I do not know the Adtran Netvanta 3430 Router
I can not log into Adtran Total Access 624 Router
SOURCE: Forgot password of Adtran NetVanta 1224R Switch
Recovering passwords requires direct physical access to a unit. This procedure cannot be performed remotely over Telnet, SSH, or the Web GUI. Connect a straight through serial cable to the console port of the unit. Configure a VT100 session (i.e. HyperTerminal or ProComm) using the following settings: 9600 bps, 8 bits, no parity, 1 stop bit and no flow control. Reboot the unit by removing the power. As the unit boots, you will be given the opportunity to break into bootstrap mode by pressing the ESC key within 5 seconds. While in the monitor mode issue the following commands: Bootstrap# bypass passwords Bootstrap# boot
Check Out the Mobile Browsers Report View all Fixya Reports
Top Adtran Computers & Internet Experts Gareth Tomlinson Level 2 Expert 116 Answers
Jax Planet Level 2 Expert 922 Answers
Notice that you are issuing the boot command not the reload command following the bypass passwords command. Once the unit has finished booting up, you can issue the enable command and you will not be required to enter the privileged (i.e. enable) password. Once you are in privileged mode, you can view the configured passwords by using the show run command. A new password can also be entered by going into global configuration mode by using config terminal command and issuing the enable password command where is the new password. Also remember to change any Telnet, SSH or Web GUI passwords if necessary.
Level 3 Expert 18410 Answers
Are you an Adtran Computer and Internet Expert? Answer questions, earn points and help others
Below is a sample output of these steps: Router (1200990L1) Executing bootstrap... ram: 268435456 bytes of RAM detected. Serial Number: LBADTNXXXXXXXXX Bootstrap version: 11.03.00, checksum: 0F3C, Thu Feb 09 17:40:34 2006 vfs: NONVOL: 120 tracks, 128 sectors/track, 1024 bytes/sector. eth0/1: initializing... eth0/1: MAC address is 00:A0:C8:XX:XX:XX bootstrap: Checking boot configuration... bootstrap: Primary image is 'NONVOL:/NV5305A-12-01-07bE.biz'. bootstrap: User escaped to command line interface. cli: starting command line interface... cli: starting user interface Press '?' for help. bootstrap#bypass passwords bootstrap#boot Posted on Mar 20, 2009 Helpful
Add Your Answer
Manuals & User Guides
Have a manual for Adtran NETVANTA 1234 POE 24PT LAYER2 SWCH POE 1700595G1 Ethernet Switch? Upload a Manual (+5pts) Or just drag it here!